220v 800w Er11 CNC Air Cooled Spindle Motor 65mm DIY Air Cooling 4 Bearings CNC Motor Spindle 65mm Aluminium Bracket Clamp

1 PCSX 800W AirCooled Spindle ER11 220V 4Bearings 65mm1 PCSX 65mm BracketSize:65x181mm(Body diameter:65mm; Length:181mm)Speed Ways:Through 3-phase output inverter and adjust the inverter to change the spindle speed.Cooling:Air coolingPower Interface:Optional H17-4 pinswaterproof air . Theair marked "1 ","2"," 3","4", "1 ","2 ","3" were connected to inverter(U, V, W), 4 connected inverter ground.(Pay attention! our spindle "4" connecting to GND,promised personal safety!!)Power:0.8kw(1HP=0.735kw)Voltage:220vAC(If you need 110v/380v spindle ,please leave message to us,thank you)Current:3A0-400HzSpeed:0-24000rpmRunout Off:0.01mm(High accuracy)Bearing Type:2X7002 P4 DT and 2X7000 P4 DTFully sealed angular contact bearingsCollet:ER11Clip Knifediameter:7mm,6.35mm,6mm,5mm,4mm,3.175mm,3mm,2mm,1mmAir Cooling ER11collet chunkGrease LubricationMain Application:Engrave for wood,bamboo,normal PCB,PVC,PMMA,plastic,duotone board(ABS)and etc nonmetal,also can engrave on gold,silver,copper,aluminium,Pb etc soft metal surface working.(Please pay more attention, this is wood working spindle, only can used for wood working and aluminum working,please don't use it for steel.If you need steel working,please check the metal spindle,thank you!)Bearing is P4 grade,2×7002 P4 DT &27000 P4 DTincrease spindle lifeHigh speedhigh torquelow noise,low price.High precision,runout off less than 0.01mm.Coaxial degree less than 0.0025mm.1. Our Ceramic ball bearings spindle use 4 pcs ceramic ball bearings.2. Ceramic ball bearings are resistant to high temperatures and low heat , usually 3-5 degrees lower than steel ball bearings during using .3. Ceramic ball bearings have low friction, low noise and long service life.4. If you want to use the spindle for aluminum, hard wood, then ceramic ball bearings better than steel ball bearings.Diameter: 65mmMaterial: Cast AluminiumFeaturesCompared with the aluminium profile fixture,the accuracy is much higher , and it is hard to deform.Inner wall is very smooth, outer walls is sandblasted, relatively fine uniform, but not very smooth.Cast aluminium fixture is much heavier than aluminium profile fixture.Product DescriptionCast aluminium fixture is aluminium which is casting with a special manufacturing process ,compared with ordinary aluminium ,This product has toughness, strong shock resistance, high hardness and strong antioxidant activity.UsageCast aluminium fixture is mainly used for fixation of ancillary products, thereby ensuring the verticality of balancing and ancillary products, ancillary products to improve running accuracy, reduce noise, reduce the accumulated error.Spindle working environment temperature is usually -10 ~ 40 .Before installing the first electric spindle axis head turned by hand, should feel flexible, non-blocking phenomenon.Spindle in the preservation and transportation, high-speed grease inside the bearing state will change, customers should be running at low speed for 30 minutes. 3000 rpm and then follow the poor increase, run 20 minutes each. Spindle and the inverter should be working together. The inverter's specifications and parameter need match spindles parameter.Connect the inverter spindle, three-phase inverter power cord should be soldered in the 1 (U), 2 (V), 3 (W) feet. After the power is turned on, to observe whether the spindle rotation axis indicates the direction consistent. If inconsistency should be immediately shut down, replace the inverter and spindle connected two wires of three-phase power supply.It should ensure that before use of water-cooled spindle, the cooling system is working properly. Every day before using the spindle must be running at low speed for 15-20 minutes. Clamping the cutters to spindle, collet nuts ,collets,cutters must be clean enough. Shank inserted into the collet must be greater than 15mm.Spindle power supply connected rated voltage, should be consistent withthe technicalparameters of the electro-spindle, spindle speed can be adjusted to change the, and voltage is proportional to the change.Spindle being not used, the application of compressed air to blow the pipes static coolant.To prevent , clogging water holes. Spindle appearance should be oiled. Plus the shaft protection device, put in a dry place.To replace the spindle bearings, certain professional and technical personnel should be replaced.Supporting special tools, bearings should be replaced fully cleaned without removing the stator coils.Beforeshipping,wedidtheoilsealtoavoidtherustduringthelongshipment.Whenyougetthespindle,pleaseclearingtheoilsealbeforeusing.Thankyou.1. Cooling in different ways: water-cooled spindle motor is the use of the water cycle to cool the heat generated after the high-speed rotating spindle, spindle motor with fan-cooled approach to cooling.2. Noise: Water-cooled spindle motor is basically no noise, but the air-cooled spindle motor is very loud.3. Life aspects: Water-cooled spindle motor pay attention to maintenance, frequently changes the water or the use of industrial water coolers, air-cooled spindle fan mainly by the wind blowing the heat transferred to the heat sink, so as to achieve the cooling effect.4.If you need use for metal ,hard wood,granite,stone,you can choose metal spindle.Metal spindle much better than wood spindle.Spindle from the production - assembly - test, and finally the perfect packaging.Origin : Mainland ChinaDrive : MotorMaximum Torque : 0.28N.mOperating Speed : 0-24000rmpModel Number : 800w ER11 air cooled spindle motor kitsApplication : Millingspindle Size : 65x181mm (65mm Diameter)Voltage : 220vCurrent : 3APower : 800w (0.8kw (1HP=735W))Cooling : Air cooledBearing type : 2x 7002C P4 DT & 2x 7000C P4 DTCollet : ER11400HzCollet Range : 1-7mm (Including 1/8,1/4 )Bracket : 65mm

• BQHHWTZ 220v 800w Er11 Cnc Air Cooled Spindle Motor 65mm DIY Air Cooling 4 Bearings Cnc Motor Spindle 65mm Aluminium Bracket Clamp